7/45°C: 30 kW heating
Input is printed as 10.68 kW. This is 2 kW below the catalogue title; the reviewed publication does not explain the difference.
Read the sourceEQUIPMENT / MODEL REFERENCE
Reciye RBDHN-32AFWN split heating unit
Read the three published temperature points, resolve the 32 kW title discrepancy, and prepare a model-specific heating enquiry.
From Guangdong Reciye HVAC Technology Co., Ltd.
Individual product research · HVACDeck Editorial · Sources checked 2026-10-11
Start with the heating duty, not the catalogue number
Reciye publishes this split air-source heating unit under a 32KW title. The attached parameter image identifies RBDHN-32AFWN and gives three different heating-output/input-power pairs. The first is 30/10.68 kW at the printed 7/45°C condition, so the title alone cannot be used as the system's design-temperature output.
This reference is useful to a buyer considering a split heating system who can provide a building heat-loss calculation and the required emitter water temperature. It does not establish a domestic-hot-water, swimming-pool or cooling duty for this model. Those applications need their own matched documentation.
The model code and numerical entries below were read from the manufacturer's actual image on 11 October 2026. The catalogue does not define all test conditions or the complete delivered arrangement. This brief therefore separates published values from project questions rather than producing an unsupported selection recommendation.
Published parameters and their scope
The catalogue identifies a model reference; confirm the current revision and selected options.
- Model
- RBDHN-32AFWN
- Rating conditions
- Source temperature pairs: 7/45°C, −12/41°C, −20/41°C. Air/water definitions, wet-bulb, flow and defrost basis not stated.
- Power supply
- 220 V ~ 50 Hz; phase/supply arrangement not stated
Swipe the table, or focus it and use arrow keys, to read the conditions and sources.
| Parameter | Published value | Conditions and evidence |
|---|---|---|
| Model | RBDHN-32AFWN | Printed on the model parameter image; not inferred from the 32KW title. Source |
| Heating output / rated power at 7/45°C | 30 / 10.68 kW | Temperature notation transcribed as printed. Air/water definitions, flow and test standard are not supplied. Source |
| Heating output / rated power at −12/41°C | 22.5 / 9.36 kW | A separate printed condition, not an output range at all ambient temperatures. Source |
| Heating output / rated power at −20/41°C | 20.16 / 11.04 kW | No measured output at the separately stated −35°C operating limit is established. Source |
| Supply | 220 V ~ 50 Hz | Phase, maximum current, protection and complete-unit connections are not identified. Source |
| Outdoor / indoor dimensions | 1100 × 478 × 843 mm ×2 / 512 × 210 × 698 mm | The outdoor ×2 notation is retained. Ask for the arrangement drawing and packing list. Source |
| Ambient range | −35 to 46°C | Manufacturer operating-range statement; not a heating-capacity or efficiency guarantee across that range. Source |
| Controls / installation wording | Wired control / Wi-Fi; externally mounted / vertical | Published options; selected accessories and mounting arrangement require confirmation. Source |
| Suggested area | 150–210 m² | No building heat-loss, insulation or indoor design basis supplied. Not a platform sizing rule. Source |
Selection and application review
Compare like conditions before comparing quotations
The image's three pairs demonstrate why the headline size is an incomplete comparison. A competing offer must use the same agreed air and water conditions and the same scope for input power. The printed slash notation is not a complete test description. Do not interpolate a new rating or calculate a certified efficiency from these entries.
Request a current selection sheet that defines outdoor air, water inlet/outlet temperatures and flow, the test standard, treatment of defrost and whether pumps or auxiliary heaters are included in input power. These are procurement clarifications; this page does not claim the unit includes every named component.
−12/41°C: 22.5 kW heating
Input is printed as 9.36 kW. Water-temperature notation differs from the first point, so these entries do not isolate outdoor temperature alone.
Read the source−20/41°C: 20.16 kW heating
Input is printed as 11.04 kW. No output at −35°C is published in this image; operating availability and required heating duty are separate questions.
Read the sourceMove from a building requirement to a supplier selection
The 150–210 m² suggestion does not identify how much heat a particular building loses. Two buildings with the same area can need different duties and different emitter temperatures. This page cannot select the unit from floor area alone. Ask the responsible designer to establish the load and send the resulting conditions to the supplier.
Define the required heating condition
Supply the project location, design outdoor and indoor temperatures, calculated heating load and the required water temperatures. Identify radiators, fan coils or underfloor circuits rather than writing only an area.
Obtain the matched model selection
Ask for RBDHN-32AFWN's current selection at those conditions, including output, input-power scope and defrost treatment. Request an explanation of the 32KW title versus the image's 30 kW first point.
Review the complete system arrangement
Have the designer and supplier agree hydraulics, controls, freeze protection and any required auxiliary heat. A catalogue operating-range claim does not settle the complete system design.
Identify what is delivered and how it connects
The sheet lists indoor dimensions and an outdoor dimension followed by ×2. That notation should stay visible until the supplier explains the selected arrangement; it does not justify inventing a two-module hydraulic or refrigerant schematic. Ask for the delivered-component schedule, shipping count and installation drawing.
No refrigerant identity, pipe sizes, permissible interconnecting run, elevation limit or required water flow was established in the reviewed image. Likewise, the voltage line does not supply maximum current or protective-device sizing. These gaps affect the installation quotation and cannot be filled from another model's sheet.
Published: sizes and control options
The image gives physical dimensions, wired/Wi-Fi control wording and installation options. Use these as a starting point for the actual layout and accessory schedule.
Read the sourceUnresolved: connections and protection
Request the selected model's hydraulic, refrigerant and electrical diagrams, service clearances and protective requirements. No minimum clearance or pipe length has been invented here.
Prepare a useful quotation and acceptance brief
Send one consistent requirement to each bidder. Identify the model, design-condition duty and the delivered scope so a catalogue headline is not compared with another supplier's project selection. This is an editorial request outline, not the manufacturer's acceptance procedure.
State the project and required duty
Model under review: RBDHN-32AFWN. Include destination, quantity, calculated load, outdoor design condition, emitter temperatures and site supply. List domestic hot water separately if needed; it is not established as a duty here.
List the documents required with the offer
Current selection and complete test basis; 32KW/30 kW clarification; delivered-component list; model-specific connection and installation drawings; destination conformity documents with matching model scope.
Agree handover evidence before ordering
Request commissioning requirements, measured acceptance conditions, operating manual, warranty and support terms. Agree how the supplier will resolve a duty shortfall; no warranty duration or commissioning result has been assumed.
Recognize the remaining evidence gaps
The official product page and image establish a catalogue publication, not independent performance testing. A published ambient range does not demonstrate output throughout the range, Wi-Fi wording does not establish a particular app or remote-service commitment, and floor area is not a project heat-loss calculation.
No model-specific independent certificate, complete test report, service-life claim, delivered price or stock availability has been verified for this brief. Ask for documents matching the ordered revision and destination. Missing public evidence is recorded as unknown, not evidence that no document exists.
The linked manufacturer profile covers the company separately. Company capabilities and historical application descriptions should not be converted into tested performance of this particular model.
Sources and review scope
Compiled by HVACDeck Editorial. Source review identifies what the publication states; it is not an independent performance test or certification.
- Reciye 32KW split heating-unit product pageChecked 2026-10-11 · Official publication re-opened; title and linked image confirmed. Sparse text does not establish a complete selected configuration.
- RBDHN-32AFWN original parameter imageChecked 2026-10-11 · Image visually read: model, three pairs and conditions, supply, sizes, controls, ambient range and suggested area. No performance test conducted.
Editorial method and corrections · Report a detail with this page URL
Turn the evidence into an enquiry
Send the manufacturer your required duty, installation conditions and the unresolved items identified in this brief.